Elastomer Totally Explained

Everything about Elastomer totally explained

An elastomer is a polymer with the property of elasticity. The term, which is derived from elastic polymer, is often used interchangeably with the term rubber, and is preferred when referring to vulcanisates. Each of the monomers which link to form the polymer is usually made of carbon, hydrogen, oxygen and/or silicon. Elastomers are amorphous polymers existing above their glass transition temperature, so that considerable segmental motion is possible. At ambient temperatures rubbers are thus relatively soft (E~3MPa) and deformable. Their primary uses are for seals, adhesives and molded flexible parts.

Background

Elastomers are usually thermosets (requiring vulcanization) but may also be thermoplastic (see thermoplastic elastomer). The long polymer chains cross-link during curing. The molecular structure of elastomers can be imagined as a 'spaghetti and meatball' structure, with the meatballs signifying cross-links. The elasticity is derived from the ability of the long chains to reconfigure themselves to distribute an applied stress. The covalent cross-linkages ensure that the elastomer will return to its original configuration when the stress is removed. As a result of this extreme flexibility, elastomers can reversibly extend from 5-700%, depending on the specific material. Without the cross-linkages or with short, uneasily reconfigured chains, the applied stress would result in a permanent deformation.
Temperature effects are also present in the demonstrated elasticity of a polymer. Elastomers that have cooled to a glassy or crystalline phase will have less mobile chains, and consequentially less elasticity, than those manipulated at temperatures higher than the glass transition temperature of the polymer.
It is also possible for a polymer to exhibit elasticity that isn't due to covalent cross-links, but instead for thermodynamic reasons.

Mathematic justifications

Using the laws of thermodynamics, stress definitions and polymer characteristics (complete derivation in [1], pages103-105), we find ideal stress behavior:

sigma = n k T [ lambda _ 1 ^ 2 + lambda _ 1 ^  ]

where

n

is the number of chain segments per unit volume,

k

is Boltzmann's Constant,

T

is temperature, and

lambda _ 1

is distortion in the 1 direction.
These findings are accurate for values of up to approximately 400% strain. At this point, alignment between stretched chains begins to result in crystallization from noncovalent bonding.
While Young's Modulus doesn't exist for elastomers due to the nonlinear nature of the stress-strain relationship, a "secant modulus" can be found at a particular strain.

Examples of elastomers

Unsaturated rubbers that can be cured by sulfur vulcanization:

Natural Rubber (NR)
Synthetic Polyisoprene (IR)
Butyl rubber (copolymer of isobutylene and isoprene, IIR)
- Halogenated butyl rubbers (Chloro Butyl Rubber: CIIR; Bromo Butyl Rubber: BIIR)
Polybutadiene (BR)
Styrene-butadiene Rubber (copolymer of polystyrene and polybutadiene, SBR)
Nitrile Rubber (copolymer of polybutadiene and acrylonitrile, NBR), also called Buna N rubbers
- Hydrogenated Nitrile Rubbers (HNBR) Therban and Zetpol
Chloroprene Rubber (CR), polychloroprene, Neoprene, Baypren etc. (Note that unsaturated rubbers can also be cured by non-sulfur vulcanization if desired).

Saturated Rubbers that can't be cured by sulfur vulcanization:

EPM (ethylene propylene rubber, a copolymer of ethylene and propylene) and EPDM rubber (ethylene propylene diene rubber, a terpolymer of ethylene, propylene and a diene-component)

Epichlorohydrin rubber (ECO)

Polyacrylic rubber (ACM, ABR)

Silicone rubber (SI, Q, VMQ)

Fluorosilicone Rubber (FVMQ)

Fluoroelastomers (FKM, and FEPM) Viton, Tecnoflon, Fluorel, Aflas and Dai-El

Perfluoroelastomers (FFKM) Tecnoflon PFR, Kalrez, Chemraz, Perlast

Polyether Block Amides (PEBA)

Chlorosulfonated Polyethylene (CSM), (Hypalon)

Ethylene-vinyl acetate (EVA) Various other types of elastomers:

Thermoplastic elastomers (TPE), for example Elastron, etc.

Thermoplastic Vulcanizates (TPV), for example Santoprene TPV

Thermoplastic Polyurethane (TPU)

Thermoplastic Olefins (TPO)

The proteins resilin and elastin

Polysulfide RubberFurther Information

Get more info on 'Elastomer'.

External Link Exchanges

Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:

<a href="http://elastomer.totallyexplained.com">Elastomer Totally Explained</a>

Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned.